Как исправить ошибки KERNEL_SECURITY_CHECK_FAILURE типа "синий экран" (0x00000139).

Возникают ситуации, когда при работе с Windows появляется синий экран (BSoD) с ошибкой Kernel Security Check Failure. Если ситуация повторяется постоянно, это может быть симптомом серьезных ошибок на жестком диске или в оперативной памяти. Рассмотрим, как её исправить.

В зависимости от причины неисправности и версии операционной системы, упомянутый синий экран может содержать полное наименование ошибки или только код 0×00000139. Компьютер обычно зависает через 5-30 минут от момента включения.

Иногда через ошибку c синим экраном вообще не получается загрузить ноутбук или компьютер, тогда попытайтесь запустить его в безопасном режиме. Для этого при включении нажмите соответствующую клавишу F или Esc (зависит от производителя). Если безопасный режим не работает должным образом, запустите систему с загрузочного диска или флешки.

Переустановка Windows в общем не обязательна, но может быть потребуется.

Шаг первый: Сканирование

Первое, что нужно сделать для диагностики проблемы, просканировать жесткий диск с помощью встроенной утилиты Chkdsk. Для этого, откройте меню Пуск и в поле системного поиска введите команду:

chkdsk /f C:

При следующем включении компьютера, прежде чем загрузится Windows, будет просканирован системный раздел С. Следует помнить, что проверка может занять длительное время.

Шаг второй: Проверка системных файлов

Синий экран с ошибкой 0×00000139 часто возникает при повреждении системных файлов. Для проверки кликните правой кнопкой мыши на кнопку Пуск и выберите пункт «Командная строка (администратор)».

В окне командной строки наберите:

sfc /scannow

Шаг третий: Проверка оперативной памяти

На этом этапе следует проверить оперативную память. Для этого в поисковую строку меню Пуск впишите «Диагностика памяти». Диагностику можно запустить сразу (после перезагрузки) или запланируйте её при следующем включении компьютера.

После обязательно запустите полную проверку антивирусом.

Шаг четвёртый: Обновление драйверов

Если вышеуказанные шаги не принесли желаемых результатов, нужно сделать следующее. Эта процедура может показаться трудоемкой, но в большинстве случаев решает проблему. Речь идет об обновлении драйверов всех компонентов.

Перейдите в Диспетчер устройств. Нажмите по отдельности на каждый компонент правой кнопкой мыши и выберите пункт «Обновить драйвер». Могут потребоваться диски с драйверами компонентов ПК, а в некоторых случаях придётся искать их на официальных страницах производителей.

Если эти меры окажутся неэффективными и синий экран с 0×00000139 продолжает появляться, остаётся только переустановить Windows. В этом случае лучше не использовать функцию восстановления, а сразу отформатировать системный диск С и сделать чистую установку операционной системы.

If you are reading this article, it means that you have gotten the Kernel Security Check Failure (BSOD) error.

However, the most common reason is that the drivers you were using for the previous Windows version are not compatible with the new Windows version.

As a result, the OS gives you the ‘Kernel Security Check Failure’ error message followed by the 0x000000139 error code .

How to remove Kernel Security Check failure

In this article, we’ll explain why this issue occurs and how you can fix it.

There are two possibilities to this issue, either you can get into your Windows 8.1 or Windows 10 PC and from time to time you get the “Kernel Security Check failure” Blue Screen of Death, or you simply cannot log in to your operating system and your device gives you this error message every time you power it up.

If you cannot log in at all into Windows 8.1 or Windows 10 then follow the steps below:

The annoying Kernel Security Check Failure error also occurs in the following situations:

  • Kernel Security Check Failure after sleep — this error may occur after waking your PC from sleep.

I have an HP Envy laptop and sometimes when it wakes up from sleep I get a blue screen saying that a problem has occured, its collecting necessary information and gives me the error KERNEL_SECURITY_CHECK_FAILURE. After it reaches 100% on collecting the info it seems to get stuck doing nothing and I am forced to hold the power button in order to turn the laptop off, then turn it on again.

  • Kernel Security Check Failure after RAM upgrade — users report that this error message sometimes occurs after they insert a new RAM memory card.

have just tried to upgrade the RAM on my laptop from 2x 2gb to 2x4gb.
when I install the RAM and boot start the computer I get the “KERNEL SECURITY CHECK FAILURE” message.
I have gone into the bios and it seems to recognize the new ram as it shows the computer as having 8gb of RAM but when booting up the failure screen comes up just after the windows logo fist appears. I have replaced the old RAM back in and it seems to start up fine. any ideas of what I could do to fix this issue?

  • Kernel Security Check Failure when playing games — if there is one thing that gamers hate, that is getting interrupted when playing their favorite games. If you’re a gamer, you probably already encountered this error quite a few times.

It had been working before, but recently, every time I try to run The Witcher 3 (just that game) I get the BSOD and informed of a KERNEL_SECURITY_CHECK_FAILURE error.

  • Kernel Security Check Failure when using particular apps and programs — it seems that particular apps and programs trigger the kernel security error more frequently than others.

Steps to fix Kernel Security Check errors

Solution 1- Enable legacy advanced boot menu

  1. Restart your computer and insert a Windows 10 bootable media into the optical media drive. For more information on how to create a Windows 10 bootable media, check out .
  2. On the displayed Windows Setup box, click Next
  3. On the next page, click Repair your computer
  4. On the ‘Choose an option’ screen, click Troubleshoot
  5. Click ‘Advanced options’
  6. Now select Command Prompt
  7. On the newly opened Command Prompt window, type C: and hit Enter.
  8. On C: prompt, type the following command and press Enter to enable legacy advanced boot menu:
  9. Once the command executes successfully, type EXIT to close the window.
  10. Go back to the ‘Choose an option’ screen, click Continue and start your computer normally.

If this didn’t help, use the solution below.

Solution 2 - Use System File Checker and Memory Diagnostic

  1. If your Windows 10 fails to start correctly, go to Settings , select Advabced Startup open the ‘See advanced repair options’ menu
  2. In the new window, left click or tap on Troubleshoot
  3. Go to Advanced Options and click or tap on Startup Settings .
  4. Left click the Restart button located in the lower right side of the screen.
  5. Your operating system should boot with the minimum system requirements.
  6. When your PC has booted, move the mouse over to the upper right side of the window.
  7. Left click the Search feature located in the menu.
  8. In the search box, type cmd.
  9. Launch Command Prompt as a Administrator.
  10. Type the following command: sfc /scannow and hit Enter.
  11. Wait until the scanning process completes. Type ‘Exit’ to close the Command Prompt window and hit Enter.
  12. Move the mouse cursor again over to the upper right side of the screen.
  13. Go to the Search feature.
  14. In the search box, type memory and select Windows Memory Diagnostic
  15. Run as administrator and select ‘Restart now and check for problems’
  16. After reboot, the OS will automatically check your RAM memory and display the possible reasons as to why you get the Blue Screen of Death error.
  17. Reboot your PC normally.
  18. Check to see if the Kernel Security Check Failure BSOD error persists.

Solution 3 - Check the memory slot

Don’t forget to check the memory slot to make sure it’s properly placed into the socket and functioning correctly.

Note: It is always a safe bet to try and replace the memory slot or change the slot in which it is plugged into the motherboard. Reboot your PC to see if the issue persists.

Solution 4 - Check your hard drive

Make sure that your hard drive functions correctly. More specifically, make sure that it is plugged in correctly into your device. If you have a spare hard drive, try changing it to see if it starts correctly.

Now, if your operating system starts and only gives you this Kernel Security Check Failure error occasionally, continue with the following steps below.

Solution 5 - Update your PC

Solution 6 - Scan your PC

Run a full system scan to detect and remove any virus or malware that potentially sneaked into your PC. may cause various issues on your computer, including the Kernel Security Check Failure error.

Perform a full system scan in order to detect any malware running on your computer. You can use , or solutions.

We recommend Bitdefender – rated as Nr. 1 world’s best Antivirus it will find all the malware on your PC and completely eliminate the threats.

  • Download Bitdefender Antivirus (50% off on all plans)

Here’s how to run a full system scan on Windows 10 Creators Update:


Note: If the antivirus cannot remove the malware it detected, first you should try installing a different antivirus to see if it works.

Note: This process can be time consuming. Depending on the hard drive’s memory, it can go between half an hour and two hours before it is done.

Solution 8 - Kernel Security Check Failure after overclock

If you overclocked your PC, this may explain why you’re experiencing Kernel Security Check Failure errors. Revert your PC to its default configuration and uninstall any running on it.

Then restart your device to see if the error persists.

Solution 9 - Run System Restore

If the problem started recently, run System Restore. If this issue occurred after you installed new software on your computer, this tool helps you to remove recently added apps and programs.

The System Restore option allows you to restore the previous well-performing system configuration without losing any files, except for a few customizable features and settings.

Solution 10 - Run Safe Mode

If you don’t want to reset your computer, you can try to boot your computer in in order to identify if there are any apps or software that are causing this problem.

For a step-by-step guide on how to enable Safe Mode, go to Microsoft’s support page .

If the problem doesn’t occur in Safe Mode, this indicates the problem is indeed triggered by an app or software.

Enable your programs one by one in order to identify the culprit. Once you’ve done that, you can uninstall the problematic software.

The steps above showed you how to fix the “Kernel Security Check failure” error message on your Windows 8.1 or Windows 10 PC.

However, if there is a hardware failure of the HDD or the RAM memory in your device, you will most likely have to replace it with a new one.

If you have any additional questions regarding this subject, please don’t hesitate to write us in the comments section below and we will help you further as soon as possible.

Here are some other similar problems that we’ve talked about in the past and you might be interested in:

Editor’s Note : This post was originally published in October, 2017 and has been since completely revamped and updated for freshness, accuracy, and comprehensiveness. Thus, this article contains up-to date information to reflect solutions available in 2019 to fix one of the most annoying BSODs in Windows 10.

Last updated on April 11th, 2018

The KERNEL SECURITY CHECK FAILURE blue screen error can occur on Windows 10 or 8 based computers, after a Windows or a driver update. Additionally, the error may appear at the end of the Windows 10 or 8 setup process (fresh Windows installation).

The symptoms of the blue screen problem "KERNEL SECURITY CHECK FAILURE", is that Windows crashes randomly or crashes during the boot process, making it impossible to enter at Windows environment. From my experience, I suppose that the above BSOD error is related to hardware or software incompatibility issues.

In this tutorial you "ll find detailed instructions to resolve the boot error "KERNEL_SECURITY_CHECK_FAILURE" in Windows 10 or Windows 8/8.1 OS.

How to FIX BSOD ERROR: KERNEL SECURITY CHECK FAILURE.

Notes before troubleshooting the "KERNEL SECURITY CHECK FAILURE" issue, by following the methods below:

1. If you face the "KERNEL SECURITY CHECK FAILURE" problem, after upgrading your system (e.g. you have added more RAM or you have replaced the VGA adapter or another component), then probably this is the reason of the blue screen problem.
2. If you face the "KERNEL SECURITY CHECK FAILURE" error, after a Windows update, then .
3. Make sure that your system is clean from viruses and malicious programs, by following this guide: .
4. Install all available Windows updates.
5. If you can login to Windows normally or in , follow the instructions in .
6. If you cannot login to Windows (Windows fails to boot), then read the instructions at .
7. To make your life easier, .

Part 1. Fix BSOD KERNEL SECURITY CHECK FAILURE using Windows Environment.

Method 1: Force Windows to Full Shutdown.

Perform a full shutdown of your system in order to re-initialize Windows at boot. To do that:

1. Click at the Power button and while holding down the SHIFT key on your keyboard, click Shutdown .

2. Power ON your computer again.
3. Check if the "BSOD KERNEL SECURITY CHECK FAILURE" problem has resolved. If it does, then permanently.

Method 2. Perform a Clean Boot.

The second method to resolve the "KERNEL SECURITY CHECK FAILURE" blue screen error, is to load Windows with the minimal set of drivers and programs in order to find out if a device driver or program cause your system to crash. To perform a clean boot:

1. Press Windows + “R ” keys to load the Run dialog box.
2. Type and press Enter to open System Configuration utility.

3. At Services tab, check the Hide all Microsoft services checkbox and click the Disable all button.

4. Then select the Startup tab and click Open Task Manager .

5. Select one by one all startup programs and click Disable .

6. Close Task Manager.
7. Press OK at System Configuration utility and restart your computer.
8. If after the restart, your computer is working without problems, then probably a device driver or a software that was running at Windows startup, caused the problem. At this case, run the System Configuration utility again and enable one-by-one the disabled programs and services (and restart), until you find out which one caused your system to crash.

Method 3. Rollback or Update the Driver for the Display Adapter (VGA).

Commonly the "KERNEL SECURITY CHECK FAILURE" error happens after updating the driver for your display adapter driver or because – at fresh Windows installations – the correct display driver is not installed. To resolve these problems:

1. Press Windows + “R ” keys to load the Run dialog box.
2. Type and press Enter .

3. In device manager, expand the Display Controllers.
4.
Right click on the installed Display Adapter * and select Properties .

* Note: If you see here a "Standard Microsoft Display Controller", then download and install from the manufacturer"s support website, the latest drivers for the display adapter.

5. Select the Driver tab and perform the following actions:

a. If the button is active, then press it to rollback to the previous version of the display driver.
b. If the button is inactive (like in screenshot below), then navigate to VGA manufacturer"s support site to download and install an older driver version for your display adapter.

6. If any of above steps, doesn"t resolve the KERNEL SECURITY CHECK FAILURE blue screen issue, then completely uninstall the display adapter from your system and reinstall. To do that:

a. Click the "" button.
b. At the warning window, check first the "Delete the driver software for this device " checkbox and click Uninstall .

7. Restart your computer.
8. After the restart, proceed and reinstall the necessary driver software for your VGA device.

Method 4. Scan & Repair Windows System files.

1. Open Command Prompt as Administrator. To do that:

a. In the Search box type: cmd (or command prompt ).
b. Right click on the command prompt (result) and select Run as Administrator .

2. In the command prompt window, type the following command & press Enter :

  • sfc /scannow

3 . Wait until Windows scans and repairs the system files.
4. When the System file check and repair is completed, restart your computer and check if your computer works smoothly.

Method 5. Check and Repair File System with CHKDSK.

Then next step is to check the hard drive for problems by using the CHKDSK command. To do that:

1. Open an Command Prompt as Admin.
2. In the command prompt window, type the following command* and press Enter :

  • C : /f /r

3. When the CHKDSK command operation is completed, restart your system.

– if none of the above methods solved the problem, then navigate to .

Part 2. Fix BSOD KERNEL SECURITY CHECK FAILURE using Windows Recovery Environment.

If you cannot boot to Windows, then you have to start from a Windows installation media to resolve the blue screen problem. If you don"t own a Windows Installation Media, then you can create one (corresponding to your Windows Edition and Version) directly from Microsoft .

Method 1. Run Startup Repair.

1.
2. At Language options, press Next .
3. Select Repair your computer .
4. Then click Troubleshoot -> Advanced Options –> Start-up Repair.

5. When the Start-up repair is completed, restart your computer.

Method 2. Check Disk and File System for Errors.

The next method to resolve Windows startup problems is to check the disk and the file system for errors. To do that, boot from the Windows installation media.

1. At the Windows Setup screen press SHIFT + F10 to access the Command Prompt, or choose Next –> Repair your computer –> Troubleshoot –> Advanced Options –> Command Prompt .

2. In command prompt, type and press Enter.
3.
Notice the drive letter of OS partition (e.g. "osdevice –> partition=D : ")

4. Then give this command* and press Enter :

  • D : /r /x

* Note: Replace the letter "D " according to your case.

5. When the CHKDSK process is completed, give this command: *

  • sfc /scannow /offbootdir= : \ /offwindir= :\windows

* Replace the " " with the drive letter where Windows are installed. In this example Windows are installed at drive D:. So the command is:

  • sfc /SCANNOW /OFFBOOTDIR=D :\ /OFFWINDIR=D :\windows

6. After SFC scan, type exit to close command prompt window and reboot your computer.

Part 3. Other Methods to resolve the KERNEL SECURITY CHECK FAILURE on Windows 10.

Method A. Perform a System Restore.

1. Boot your computer from the Windows installation media (DVD or USB).
2. At Language options, press Next .
3. Select Repair your computer .
4. Then click Troubleshoot -> Advanced Options –> System Restore.

6. Select an earlier working state* and click Next .

* Note: Check t he Show more restore points checkbox, to view all available restore points.

7. Finally, review your selection and if you agree, press Finish and then Yes .
8. Now wait until the restore process is completed. During the restore process, your computer will restart several times and when it"s done, you should enter in Windows without problems.

Method B. Modify SATA Mode in BIOS Settings.

1. Power On your computer and press the appropriate key (DEL or F1 or F2 or F10 ) to enter BIOS settings. *

* Note: The way to enter into BIOS Settings depends on the computer manufacturer. To Enter into your BIOS Settings, pay attention at the first screen as your computer starts and try to find a message like this:

"DEL to enter setup"
"Press ESC to Enter Setup"
"BIOS Configuration: F2"
"F10 to Enter Setup"

2. Load Default Settings (Load Optimal Defaults)

3. Then look on all BIOS screens for a setting named or SATA Mode or SATA Controller Mode or SATA Operation or Configure SATA as . (This setting is commonly found under the Advanced section).

4. Make sure that the SATA Mode (Type) is set to AHCI and NOT in RAID .

5. Save Changes and Exit BIOS Settings and try to boot on Windows.

That"s it! Let me know if this guide has helped you by leaving your comment about your experience. Please like and share this guide to help others.

If this article was useful for you, please consider supporting us by making a donation. Even $1 can a make a huge difference for us in our effort to continue to help others while keeping this site free:

If you want to stay constantly protected from malware threats, existing and future ones , we recommend that you install Malwarebytes Anti-Malware PRO by clicking below (we do earn a commision from sales generated from this link, but at no additional cost to you. We have experience with this software and we recommend it because it is helpful and useful):

Summary: Don"t worry if your computer gets the blue screen of death error due to Kernel Security Check failure issue in Windows 10/8/7. This article will provide one quick fix and 4 reliable methods to help you thoroughly fix Kernel Security Check failure with BSOD error with simple clicks. Feel free to follow fix these problems and repair your computer back to work normally again.

Kernel Security Check failure with BSOD error in Windows 10/8, help!

"Hi there, do you know how to fix the Blue Screen of Death (BSOD) error after upgrading Windows system to Windows 10 or Windows 8/8/1? I"m having this issue that both two of my computers and both of these two computers had just upgraded into Windows 10 and Windows 8 yesterday.
This morning, when I tried to start these two computers and then the
BIOS error came up with the error message "Your PC ran into a problem and needs to restart. We"re just collecting some error info, and then we"ll restart for you. (10% complete) If you"d like to know more, you can search online later for this error: KERNEL_SECURITY_CHECK_ERROR". I then tried to Google the answer and it seemed that quite a lot of users are having a similar issue to me. So how can I fix this issue and get my computers out of the Kernel Security Check failure with BSOD error? "

If you happen to have a BSOD problem in your PC due to Windows system install or update but failed with Kernel Security Check error, don"t worry. Right below, EaseUS software has collected some reliable solutions including one quick fix and 4 methods to help you effectively get rid of Kernel Security Check issue from Windows 10/8/7 PC. Just follow to see how to solve these issues with ease now.

Quick fix Kernel Security Check failure with BSOD error

Here are the steps about how to boot Windows 10/8 PC into Safe Mode:

1. Press Win + R keys to open Run dialog > Type: msconfig and hit Enter.
2. Go to Boot option > Select Safe boot > OK.
If you want to boot into Safe Mode with the internet connection, select Network option under Safe boot category.
3. Click Restart so to boot your computer into Safe Mode now.

If the Kernel Security Check failure disappears after booting PC into Safe Mode, you need to check the offending programs in your PC or uninstall and update necessary drivers.
If the error still exists in Safe Mode, it"s very likely that the RAW or hard drive got something wrong.

Note: 1. If Safe Mode doesn"t help, you can directly boot PC into desktop and follow the offered solutions to fix Kernel BSOD error.

2. If you can"t boot PC into the desktop, try hard reboot:

  • Press and hold the power button on your PC till it powers off > Restart PC by pressing the power button.
  • Repeat the steps till you see Please wait comes out.
  • Click See advanced repair options > Troubleshoot > Advanced options.
  • Choose Startup Settings > Restart > Press F4, F5, F6 to try 4, 5, 6 options so to boot your PC into desktop.

Resolutions to fix KERNEL_SECURITY_CHECK error in Windows 10/8/7

Here in this part, you"ve three reliable methods to effectively fix and get rid of KERNEL_SECURITY_CHECK failure error in Windows 10/8/7 and you may selectively follow either one to get this issue fixed now:

Before you start, it"s highly recommended for you to do a full scan on your computer to remove possible virus or malware with anti-virus software.

Method 1. Repair System file and bad sectors that cause Kernel Security Check failure issue

Run System File Checker:

1. Type: cmd in the search box and right-click on Command Prompt > Select Run as administrator;
2. Click Yes to continue with administrator permission;
3. Type: sfc /scannow and hit Enter to check and repair corrupted system files which may cause BSOD error with Kernel Security Check failure;

Run partition manager:

If system hard drive or partition has bad sectors, Windows system won"t be able to boot normally. Instead, a BSOD error may come up.
Fortunately, powerful partition manager software from EaseUS will effectively help fix this issue with its Check Partition feature:

Step 1: Open EaseUS Partition Master on your computer. Then locate the disk, right-click the partition you want to check, and choose "Check File System".

Step 2: In the Check File System window, keep the "Try to fix errors if found" option selected and click "Start".

Step 3: The software will begin checking your partition file system on your disk. When it has completed, click "Finish".

Method 2. Scan and fix system hard disk error

1. Click Start > File Explorer > This PC;
2. Right-click the hard drive that you need to check and scan > Select Properties;
3. Go to Tools tab > Click Check;

There, the Error Checking tool will automatically check and fix system hard disk error that may cause a Kernel Security Check failure issue in Windows PC.

Method 3. Run Memory Diagnostic Tool to fix the Kernel Security Check failure issue

1. Press Win + R keys to open Run dialog > Type: mdsched.exe and hit Enter;
2. Choose Restart now and check for problems (recommended) to check the status of memory card right now;
Or select Check for problems the next time I start my computer;

3. Then The Memory Diagnostic Tool will automatically run to check errors on Memory card in your PC.

If no errors are checked, your memory card is working perfectly fine with no problem;
If errors are detected, change the current memory card with a new one so to get rid of BSOD with Kernel Security Check failure error.

Method 4. Try System Restore to repair PC from Kernel BSOD issue

1. Boot PC into Safe Mode; (You may follow guidelines in Quick Fix so to boot PC into the Safe Mode.)
2. Click Control Panel on Start > Choose Recovery in All Control Panel Items;
3. Click Open System Restore > Check Choose a different restore point > Next;
4. Select the exact restore point (healthy Windows restore point) which you"ve created previously and click Next > Next to continue;

5. Click Yes to confirm that you want to execute the System Restore operation.
Wait to let the System Restore process complete and then you"ll get your previous Windows system back. There, no Kernel Security Check error or BSOD issue will exist then.

Related Articles - ALSO ON EaseUS SOFTWARE

Kernel security check failure – критическая ошибка, возникающая в некоторых случаях на синем экране (он же BSoD) при работе системы.

Причину обычно определить сложно, их может быть большое множество. В версии Windows 10 к ошибке начала прилагаться определенная поясняющая информация, что немного облегчило её устранение. Выделим наиболее частые причины , вызывающие данный сбой:

  • Проблема с установленными или отсутствием необходимых драйверов.
  • Битые файлы системного реестра.
  • Конфликт какого-либо ПО с используемой версией BIOS.
  • Аппаратные неполадки компьютера (перегрев, повреждение компонентов).

Устранение неисправности

Достоверно установить причину скорее всего не удастся. Поэтому поэтапно применяем возможные методы устранения сбоя, один из которых вероятно поможет в этом случае.

Сканирование на ошибки

Прежде всего надо просканировать жесткий диск на наличие ошибок, сбойных секторов.

Можно использовать специализированные утилиты (Victoria HDD, HDD Scan, Seagate SeaTools и др.), а можно ограничиться применением штатных средств системы, что будет значительно менее эффективно.

Но все же попробуем. Для этого в проводнике отрываем свойства и вкладку Сервис того локального диска, который необходимо проверить.

Еще один способ сканирования – в командном интерпретаторе, запустите команду chkdsk /f C:, а затем Y для подтверждения выполнения проверки после перезагрузки.

Из стороннего ПО порекомендуем использовать Victoria for Windows .

Здесь можно получить много разной информации о Вашем жестком диске. Для получения картины, описывающей его состояние, перейдите во вкладку Test и пройдите тестирование, предварительно установив флажок Remap для одновременного восстановления битых секторов.

Проверяем системные файлы

Если проверка жесткого диска не дала результата, проводим сканирование файлов системы . Команда sfc /scanow в консоли от имени администратора.

Утилита проведет восстановление поврежденных файлов, если это возможно.

Проверка оперативной памяти

Далее тестируем оперативную память на наличие ошибок. Часто именно это даёт эффективный результат. Опять же, тестирование можно провести штатными средствами системы с малой вероятностью положительного решения.

Встроенное средство диагностики проверит компьютер на предмет ошибок RAM .

Порекомендуем использовать популярную утилиту Memtest86+ .

Если ошибки обнаружатся, то проще всего будет заменить сбойный модуль RAM.

Обновляем драйвера

Возможно потребуется обновить драйвер Вашего видеоадаптера. Вызываем диспетчер устройств и в свойствах своей видеокарты жмем обновить драйвер , далее подгружаем актуальный из интернета или скачиваем и устанавливаем его самостоятельно.

Восстанавливаем реестр

Повреждения реестра лучше устранять с помощью специальных программ наподобие Ashampoo Optimizer или CCleaner .

Они проведут необходимые исправления и очистку от накопившихся в системе мусорных файлов.

Если предложенные меры Вам не помогут, то из программных решений ошибки остается вариант полной переустановки системы.